main hardware index | |
Size | 42mm length * 42mm width * 3.2mm height |
connection mode | stamp hole patch type |
CPU | hisilicon hi3516dv500 dual-core a55 main frequency 850mhz |
NPU | 2 TOPs |
Memory | ddr4 standard 1gb/2gb optional 4g |
storage device | emmc 5.1 standard 8gb optional 16gb/32g/64g/128g |
power management | design of discrete power supply |
working voltage | 5v 2a or above |
support system | linux 5.10 busybox1.34.1 |
operating temperature | -10 + 75 degrees |
common interface of core board | |
MIPI DSI | support for 4lane up to support 1920x1200 |
MIPI CSI | a maximum of 4k is supported by two-way csi 4k or 2k / 2k. |
I2S | two-way i2s |
USB2.0 | usb2.0 can be otg all the way. |
USB3.0 | one way usb 3.0 |
Ethernet | 1-way rgmii ethernet interface |
UART | 6-way serial port |
SPI | 4-way SPI |
I2C | 6-way I2C |
PWM | 1-way PWM |
SDIO | 2 sdio interfaces, one for tf card, the other for wifi |
ADC | 4 analog adc input interface |
GPIO | reusable gpio up to 110, |
voice input | two-way analog voice input |
voice output | all the way to the headset output |
Upgrade | support for local upgrade of usb/ tf card |
rp-3516dv500 feature list | |||
Linux 5.10 | Remarks | ||
MIPI | mipi display screen (5-inch 720x1280 plus touch assembly) | √ | |
mipi display screen (5.5in 720x1280 plus touch assembly) | √ | ||
mipi display screen (7-inch 1024x600 plus touch assembly) | √ | ||
mipi display screen (7-inch 1200x1920 plus touch assembly) | √ | ||
mipi display screen (8-inch 800x1280 plus touch assembly) | √ | ||
mipi display screen (8-inch 1200x1920 plus touch assembly) | √ | ||
mipi display screen (10.1in 800x1280 plus touch assembly) | √ | ||
mipi display screen (10.1in 1920x1200 plus touch assembly) | √ | ||
mipi display screen (10.1in 1200x1920 plus touch assembly) | √ | ||
RTC | rtc (built-in pmu) | √ | |
rtc (plug-in hym8563, power-off time saved) | √ | ||
audio output | loudspeaker (5w/8 can be connected to the backplane to play sound) | √ | |
headset (with headset detection function) | √ | ||
audio input | microphone input | √ | |
LINE-IN | √ | ||
USB HOST | usb3.0 otg standard port a (main weight equipment switching, adb/host) | √ | |
usb3.0 host standard a port (3.0u disk / 3.0usb camera) | √ | ||
usb2.0 host standard a port (2.0u disk / 2.0usb camera) | √ | ||
usb2.0 host pin arrangement (2.0u disk / 2.0usb camera) | √ | ||
TTL | √ | ||
RS485 | √ | ||
RS232 | √ | ||
SD card | SD card | √ | |
upgrade button (long press the power to enter the burning mode) | √ | ||
Power key | √ | ||
spi driver | √ | ||
i2c driver | √ | ||
pwm driver | √ | ||
sdio driver | √ | ||
gpio driver | √ | ||
usb driver | √ | ||
TP | single touch function is normal. | √ | |
multi-touch function is normal. | √ | ||
reboot multiple times touch is normal | √ | ||
LED | the led is always on during kernel startup. | √ | |
repeated insertion and unplugging can be used normally. | √ | ||
connect the equipment to boot, restart repeatedly and enter the system can be used normally. | √ | ||
ttyusb* node (cp210x,ch34x) can be generated by inserting part of usb to serial port. | √ | ||
the eth* node can be generated by inserting part of the usb network port. | √ | ||
repeated insertion and unplugging is normal. | √ | ||
plug in the boot system to recognize the status normally. | √ | ||
RTC | after power off, the hardware time is running normally. | √ | |
normal synchronization network time | √ | ||
GPIO | set the output level to normal | √ | |
the default boot output is normal. | √ | ||
set input acquisition status is normal | √ | ||
root user login account password is rpdzkj | √ | ||
debug serial port automatic login | √ | ||
power on and mount all partitions | √ | ||
open ssh root users can log in | √ | ||
install wireless network instructions such as iwconfig iw iwlist by default | √ | ||
install iperf ip route ifconfig udhcpc by default | √ | ||
the default boot automatically acquires the ip address. | √ | ||
install can bus test tools by default | √ | ||
install scp lrzsz by default | √ | ||
the sound card is configured by default, which can be played and recorded directly. | √ | ||
configure the wlan1 node by default | √ | ||
note whether the ntp server can access it. | √ | ||
functional test script | serial port test script | √ | |
audio test script | √ | ||
4g test script | √ | ||
network test script | √ | ||
RTC | √ | ||
GPIO | √ | ||
WIFI | wifi opens normally, and scan connection wifi | √ | |
wifi connection script command | √ | ||
open, connect, surf the internet is normal | √ | ||
repeat the switch and turn on normally. | √ | ||
restart can be opened automatically. | √ | ||
Ethernet | automatically get ip after connecting the network cable | √ | |
ping public network is normal. | √ | ||
the browser surfs the internet normally. | √ | ||
plug and unplug the network cable many times after power on, and connect to the network normally. | √ | ||
plug in the network cable before power on, and connect to the network normally. | √ | ||
normal use of static ip | √ | ||
4G | boot to get the network automatically, and the browser accesses the internet | √ | |
after connecting, unplug the module and plug it in to reconnect. | √ | ||
after connecting, unplug the antenna, disconnect and plug in the antenna to reconnect. | √ | ||
ping testing the stability of long-term connection | √ | ||
SD card | the sd card can be properly identified and mounted automatically. | √ | |
the file browser can read and write files normally. | √ | ||
repeated plugging and unplugging can be identified normally. | √ | ||
after the sd card is inserted, it can be powered on normally and can be identified normally. | √ | ||
U disk | the usb disk can be properly identified and mounted automatically. | √ | |
the file browser can read and write files normally. | √ | ||
repeated plugging and unplugging can be identified normally. | √ | ||
SPI | the / dev/spi node can be generated, and the test of connecting spi module is normal. | √ | |
IIC | the / dev/i2c node can be generated, and the test of connecting spi module is normal. | √ | |
UART | each baud rate communicates with the computer normally. | √ | |
multi-channel automatic transceiver is normal | √ | ||
temperature | test project | ||
25 degrees celsius | soft restart | 24 hours | PASS |
hard restart | 24 hours | PASS | |
rk stress test / cpu stress test | 24 hours | PASS | |
monkey/ random | 24 hours | PASS | |
85 degrees celsius | hard restart | 24 hours | PASS |
rk stress test / cpu stress test | 24 hours | PASS | |
monkey/ random | 24 hours | PASS | |
-40 degrees celsius | hard restart | 24 hours | PASS |
Current parameter table
Project | Minimum | Typical | Maximum | |
power supply parameters | Voltage | 11V | 12V | 15V |
Ripple | 50mV | |||
3v rtc power consumption | 0.9uA | |||
motherboard current test (no other peripherals are connected) | power-on current | 110mA | 223mA | 355mA |
desktop static current | 135mA | |||
motherboard current test connect the 7-inch 1024x600 | power-on current | 215mA | 295mA | 345mA |
desktop static current | 245mA | |||
environment | relative humidity | -- | 65% | 75% |
operating temperature | -10 ℃ | -- | 75 ℃ | |
storage temperature | -40 ℃ | -0 ℃ | 100 ℃ | |
main hardware index | |
Size | 42mm length * 42mm width * 3.2mm height |
connection mode | stamp hole patch type |
CPU | hisilicon hi3516dv500 dual-core a55 main frequency 850mhz |
NPU | 2 TOPs |
Memory | ddr4 standard 1gb/2gb optional 4g |
storage device | emmc 5.1 standard 8gb optional 16gb/32g/64g/128g |
power management | design of discrete power supply |
working voltage | 5v 2a or above |
support system | linux 5.10 busybox1.34.1 |
operating temperature | -10 + 75 degrees |
common interface of core board | |
MIPI DSI | support for 4lane up to support 1920x1200 |
MIPI CSI | a maximum of 4k is supported by two-way csi 4k or 2k / 2k. |
I2S | two-way i2s |
USB2.0 | usb2.0 can be otg all the way. |
USB3.0 | one way usb 3.0 |
Ethernet | 1-way rgmii ethernet interface |
UART | 6-way serial port |
SPI | 4-way SPI |
I2C | 6-way I2C |
PWM | 1-way PWM |
SDIO | 2 sdio interfaces, one for tf card, the other for wifi |
ADC | 4 analog adc input interface |
GPIO | reusable gpio up to 110, |
voice input | two-way analog voice input |
voice output | all the way to the headset output |
Upgrade | support for local upgrade of usb/ tf card |
rp-3516dv500 feature list | |||
Linux 5.10 | Remarks | ||
MIPI | mipi display screen (5-inch 720x1280 plus touch assembly) | √ | |
mipi display screen (5.5in 720x1280 plus touch assembly) | √ | ||
mipi display screen (7-inch 1024x600 plus touch assembly) | √ | ||
mipi display screen (7-inch 1200x1920 plus touch assembly) | √ | ||
mipi display screen (8-inch 800x1280 plus touch assembly) | √ | ||
mipi display screen (8-inch 1200x1920 plus touch assembly) | √ | ||
mipi display screen (10.1in 800x1280 plus touch assembly) | √ | ||
mipi display screen (10.1in 1920x1200 plus touch assembly) | √ | ||
mipi display screen (10.1in 1200x1920 plus touch assembly) | √ | ||
RTC | rtc (built-in pmu) | √ | |
rtc (plug-in hym8563, power-off time saved) | √ | ||
audio output | loudspeaker (5w/8 can be connected to the backplane to play sound) | √ | |
headset (with headset detection function) | √ | ||
audio input | microphone input | √ | |
LINE-IN | √ | ||
USB HOST | usb3.0 otg standard port a (main weight equipment switching, adb/host) | √ | |
usb3.0 host standard a port (3.0u disk / 3.0usb camera) | √ | ||
usb2.0 host standard a port (2.0u disk / 2.0usb camera) | √ | ||
usb2.0 host pin arrangement (2.0u disk / 2.0usb camera) | √ | ||
TTL | √ | ||
RS485 | √ | ||
RS232 | √ | ||
SD card | SD card | √ | |
upgrade button (long press the power to enter the burning mode) | √ | ||
Power key | √ | ||
spi driver | √ | ||
i2c driver | √ | ||
pwm driver | √ | ||
sdio driver | √ | ||
gpio driver | √ | ||
usb driver | √ | ||
TP | single touch function is normal. | √ | |
multi-touch function is normal. | √ | ||
reboot multiple times touch is normal | √ | ||
LED | the led is always on during kernel startup. | √ | |
repeated insertion and unplugging can be used normally. | √ | ||
connect the equipment to boot, restart repeatedly and enter the system can be used normally. | √ | ||
ttyusb* node (cp210x,ch34x) can be generated by inserting part of usb to serial port. | √ | ||
the eth* node can be generated by inserting part of the usb network port. | √ | ||
repeated insertion and unplugging is normal. | √ | ||
plug in the boot system to recognize the status normally. | √ | ||
RTC | after power off, the hardware time is running normally. | √ | |
normal synchronization network time | √ | ||
GPIO | set the output level to normal | √ | |
the default boot output is normal. | √ | ||
set input acquisition status is normal | √ | ||
root user login account password is rpdzkj | √ | ||
debug serial port automatic login | √ | ||
power on and mount all partitions | √ | ||
open ssh root users can log in | √ | ||
install wireless network instructions such as iwconfig iw iwlist by default | √ | ||
install iperf ip route ifconfig udhcpc by default | √ | ||
the default boot automatically acquires the ip address. | √ | ||
install can bus test tools by default | √ | ||
install scp lrzsz by default | √ | ||
the sound card is configured by default, which can be played and recorded directly. | √ | ||
configure the wlan1 node by default | √ | ||
note whether the ntp server can access it. | √ | ||
functional test script | serial port test script | √ | |
audio test script | √ | ||
4g test script | √ | ||
network test script | √ | ||
RTC | √ | ||
GPIO | √ | ||
WIFI | wifi opens normally, and scan connection wifi | √ | |
wifi connection script command | √ | ||
open, connect, surf the internet is normal | √ | ||
repeat the switch and turn on normally. | √ | ||
restart can be opened automatically. | √ | ||
Ethernet | automatically get ip after connecting the network cable | √ | |
ping public network is normal. | √ | ||
the browser surfs the internet normally. | √ | ||
plug and unplug the network cable many times after power on, and connect to the network normally. | √ | ||
plug in the network cable before power on, and connect to the network normally. | √ | ||
normal use of static ip | √ | ||
4G | boot to get the network automatically, and the browser accesses the internet | √ | |
after connecting, unplug the module and plug it in to reconnect. | √ | ||
after connecting, unplug the antenna, disconnect and plug in the antenna to reconnect. | √ | ||
ping testing the stability of long-term connection | √ | ||
SD card | the sd card can be properly identified and mounted automatically. | √ | |
the file browser can read and write files normally. | √ | ||
repeated plugging and unplugging can be identified normally. | √ | ||
after the sd card is inserted, it can be powered on normally and can be identified normally. | √ | ||
U disk | the usb disk can be properly identified and mounted automatically. | √ | |
the file browser can read and write files normally. | √ | ||
repeated plugging and unplugging can be identified normally. | √ | ||
SPI | the / dev/spi node can be generated, and the test of connecting spi module is normal. | √ | |
IIC | the / dev/i2c node can be generated, and the test of connecting spi module is normal. | √ | |
UART | each baud rate communicates with the computer normally. | √ | |
multi-channel automatic transceiver is normal | √ | ||
temperature | test project | ||
25 degrees celsius | soft restart | 24 hours | PASS |
hard restart | 24 hours | PASS | |
rk stress test / cpu stress test | 24 hours | PASS | |
monkey/ random | 24 hours | PASS | |
85 degrees celsius | hard restart | 24 hours | PASS |
rk stress test / cpu stress test | 24 hours | PASS | |
monkey/ random | 24 hours | PASS | |
-40 degrees celsius | hard restart | 24 hours | PASS |
Current parameter table
Project | Minimum | Typical | Maximum | |
power supply parameters | Voltage | 11V | 12V | 15V |
Ripple | 50mV | |||
3v rtc power consumption | 0.9uA | |||
motherboard current test (no other peripherals are connected) | power-on current | 110mA | 223mA | 355mA |
desktop static current | 135mA | |||
motherboard current test connect the 7-inch 1024x600 | power-on current | 215mA | 295mA | 345mA |
desktop static current | 245mA | |||
environment | relative humidity | -- | 65% | 75% |
operating temperature | -10 ℃ | -- | 75 ℃ | |
storage temperature | -40 ℃ | -0 ℃ | 100 ℃ | |
Product Show Case